Min. Shipping :£0.00
VAT (20%): £0.00
Total: £0.00
Prices in currencies other than GBP are for guidance only. The actual rate will be that used by the credit card company at the time of billing.
Over 50 types of bulb holder and harness for popular classic and vintage lighting applications, including BA7, BA9, BA15, festoon and British Pre-focus. Single and double contact, equal and offset pin, solder plug, sockets and insert options. Many holders for specific Lucas type lamps including L488, L489, L539, L594, 1130, ST38, L140, L150, L165, 576 and 700 series lamps. Please browse our full range below.
Replacement general purpose bulb holder - accepts 15mm diameter base bulbs. Offered for various bulbs configurations - 1156/SCC/BA15S single contact parallel pin, SBC/BA15D double contact parallel...
Replacement general purpose bulb holder - accepts 15mm diameter base bulbs. Offered for various bulbs configurations - 1156/SCC/BA15S single contact parallel pin, SBC/BA15D double contact parallel...
Replacement general purpose bulb holder - accepts 15mm diameter base bulbs. Offered for various bulbs configurations - 1156/SCC/BA15S single contact parallel pin, SBC/BA15D double contact parallel...
Replacement general purpose bulb holder - accepts 15mm diameter base bulbs. Offered for various bulbs configurations - 1156/SCC/BA15S single contact parallel pin, SBC/BA15D double contact parallel...
Double contact headlamp converter for most many headlamps which are mounted through the rear of reflector bowl - usually held in place in the bulb holder socket on Lucas reflectors with clamp clip...
Metal cased replacement bulbholder. outside 16.4mm x approx 23.5mm long.
Offered with single (equal pin) or double (offset pin) contacts.
Metal cased replacement bulbholder. outside 16.4mm x approx 23.5mm long.
Offered with single (equal pin) or double (offset pin) contacts.
Metal cased replacement bulbholder. outside 16.4mm x approx 23.5mm long.
Offered with single (equal pin) or double (offset pin) contacts.
Offset pin
Single contact BA15s bulbholder with wire tail. Measures outside 17mm x 26mm long. Note the two barb tags to the side to hold this in place.
Useful bulb holder (BA15) with bracket, (60mm x 16mm) which can be bent as necessary.
Useful bulb holder (BA15) with bracket, (60mm x 16mm) which can be bent as necessary.
Useful bulb holder (BA15) with bracket, (60mm x 16mm) which can be bent as necessary.
Double contact bulb holder for Lucas 1130 type side lamp, accepts double contact SBC BA15D parallel pin bulbs. Please note these are made to original pattern. These bulb holders allow conversion...
Two T10 edge base bulbs (amber for flasher, clear for sidelamp) - 12 volt and 6 volt now available! Please select required voltage from the drop down menu below.
Bulb holder for fitting into...
1130 lamp bulb holder. BA15S base for single contact, equal pin bulbs - B382 for 12v and B317 for 6V 5W
1130 lamp bulb holder. BAY15D base for double contact, offset pin bulbs - B380 for 12V and B384 for 6V 21/5w
Original pattern side light bulb holder for our 1142S lamps, equivalent to the original Lucas 1142 type side lamp. Takes bulb part numbers B205 (6V) or B207 (12V). Each bulb holder.
Modified bulb holder for Lucas 1142 type lamps including the new 'Toby' 1142S. Double contact 1158/SBC/BA15D holder. Takes incandescent bulb part numbers B383 (6V) or B381 (12V) for a 5W side...
Converted bulb holder for 1142S lamps. Provides a side light and indicator conversion for lamps equivalent to the original Lucas 1142. Takes capless bulbs, part numbers B501 and B921A (12V only).
Single contact bulb holder for Lucas L488 lamps
Twin contact bulb holder BAY15D (offset pins) for Lucas L488 lamps
Bulb holder BA15S single contact for Lucas L594 lamps
Twin contact BAY15D bulb holder (offset pins) for Lucas L594 lamps. For stop and tail or front clear side and indicator.
Double ended holder which accepts a plug or standard SCC BA15S or SBC BA15D bulb at either end. Threaded outside body.
Double ended holder which accepts a plug or standard SCC BA15S or SBC BA15D bulb at either end. Threaded outside body.
Single contact holder which accepts a plug or standard SCC/BA15S bulb...
Double ended holder which accepts a plug or standard SCC BA15S or SBC BA15D bulb at either end. Threaded outside body.
Double contact holder which accepts a plug or standard SBC/BA15D bulb...
Double ended holder which accepts a plug or standard SCC BA15S or SBC BA15D bulb at either end. Threaded outside body.
Nickel plated brass Double contact holder which accepts a plug or...
Double ended holder which accepts a plug or standard SCC BA15S or SBC BA15D bulb at either end. Threaded outside body.
Brass Double contact holder which accepts a plug or standard SBC/BA15D...
Plug for SCC and SBC type bulb holders. Offered in double contact or single contact. Cables enter through back.
Plug for SCC and SBC type bulb holders. Offered in double contact or single contact. Cables enter through back.
Plug for SCC BA15S type holder, single contact, cables enter through back.
Plug for SCC and SBC type bulb holders. Offered in double contact or single contact. Cables enter through back.
Plug for SBC BA15D type holder, double contact, cables enter through back.
Double contact BA15D bulb holder plug with solder connections - two part assembly (unscrews). To wire up, unscrew the body, push the brass connectors from the bakelite body, pass wires through the...
Double contact BA15D bulb holder plug with solder connections - two part assembly (unscrews). To wire up, unscrew the body, push the brass connectors from the bakelite body, pass wires through the...
Double contact BA15D bulb holder plug with solder connections - two part assembly (unscrews). To wire up, unscrew the body, push the brass connectors from the bakelite body, pass wires through the...
Single ended, double contact bulb holder. Dimensions thread diameter 19mm, overall length 38mm, flange 28.5mm. Accepts SBC BA15D bulb, rear nut removes to expose terminal contacts.
Double contact bulb holder insert, fits our 422 bulb holder, two spring loaded brass bulb contacts at one end with two wire terminals at the other, insulator body dimensions 16mm long x 16.7mm...
Bulb holder for Lucas L489 type side lamps - MCC/BA9S bulb holder fitting, single contact.
Twin wired base plate with 1156/SCC/BA15S single contact bulb holder with foam gasket for Lucas type L539 lamps.
76mm Outer diameter
46mm between fixing holes
Bulb holder sleeve (offset pin BAY15D) and cotton braid pig tail wires which will fit into part number 211 series 'Duolamp' type lamps to enable a small (19mm diameter) globe double contact bulb...
Replacement bulb holder divider plate for 776/ST38/'Pork Pie' type rear lamps. Accepts 3 x BA15S bulbs. Made to the original specification.
Conversion kit to modify your 776 part number or Lucas ST38/'Pork Pie' type rear lamps to also give amber turn indication. New WEDGE T10 bulbs and bulb holders, special red and amber lens. This...
High quality fibre board and copper contact British Pre-focus bulb holder/contact plate for Lucas 576 type spot and fog lamps (e.g. SLR and SFT576). Single contact, with wire tails and bullet...
High quality bakelite bulb holder for FT700 and CLR700 light units. Double contact, but one contact can be bent away to make single contact. 71.5mm OD, screw on, min ID 38.5 max ID 45mm
British Pre-focus P36D headlamp connector with lead. Double contact with three pin bayonet bulb holder, three wires with headlamp bowl sealing grommet and soldered bullet connecters, overall...
Double contact bulb holder for American Pre-Focus P15D 30 double contact base bulbs. Removeable rubber boot surround. Metal holder front plate maximum 44.5mm diameter with three spring loaded...
Double contact bulb holder for Bosch BA20D double contact base bulbs. Removeable rubber boot surround. Metal holder front plate maximum 44.5mm diameter with two locating tabs (one with small hole...
Double contact bulb holder for PX15D 25.1 MPF (Mini Pre Focus) base bulbs. 52mm diameter, removable plastic surround with three equally spaced square cut locating tabs, on a 16.5mm outer...
Double contact bulb holder for P15D 25.3 base bulbs. 52mm diameter, removable plastic surround with two locating tabs, around a 28mm metal holder/socket. Maximum depth 31mm. Two live connection...
Sealed beam headlamp connector with lead, nylon block three Lucar (6,3mm spade) connector, three wires with headlamp bowl sealing grommet and soldered bullets, overall length 850mm.
BA7S bulb holder fitted with 12V 2W bulb. Twin 6.3mm push on/Lucar rear terminal connections. For replacement bulbs please order B282 (6V) or B281 (12V)
MCC/BA9s bulb holder, 10.4mm diameter, useful general application spare for equal pin bayonet base 9mm cap bulbs. Single contact.
MCC/BA9s bulb holder. 12.3mm diameter, overall length 18.5mm, useful general application spare for bayonet base 9mm cap equal pin bulbs. single contact, supplied with connectors and terminals.
Rubber mounted flanged MCC/BA9S pilot light bulb holder. Equivalent to Lucas part number 554710. 15cm long wire tails finished in bullet connectors. shrink wrap sheath. Rubber feed through grommet...
Spring clip mounted single contact bulb holder to hold MES E10 (11mm globe diameter) 2.2W screw in bulb (B987) as back light for instrument gauges. 6 spring clips push in to a 16mm diameter hole....
Twist fit bulb holder for T10 wedge base. 15mm aperture diameter.
Black soft rubber capless bulb holder - tube type. Fits in many side light apertures and also clock and gauge backs. Supplied with wired terminals to allow fitting of capless T10 and T15 wedge...
Black hard nylon capless bulb holder - tube type. Fits in many side light apertures including Wipac type lights and also Smiths Gauges. Supplied with wired terminals to allow fitting of capless...
Black nylon capless bulb holder - tube type. Fits many side light apertures including Wipac type lights and also Smiths Gauges. Supplied with two crimp wire terminals to allow fitting of capless...
Push in plastic bulb holder for capless bulbs. Supplied with two wire crimp terminals for capless bulbs. Fits jewel lights, ST38 conversion and 1130 conversions. Dimensions main body 28mm long x...
Compact bulb holder for 39mm long festoon bulbs with spade connections and central mounting hole. 6.3mm spade connections at either end. Compact plastic body 17mm wide x 50mm long (excluding...
Compact bulb holder for 42 to 44mm long festoon bulbs with spade connections and central mounting hole. 6.3mm spade connections at either end. Compact plastic body 17mm wide x 50mm long (excluding...
Standard plastic H4 headlamp socket. 219mm high, 26mm wide and 21mm long. Supplied with three brass flag terminals for crimping on to wire and connecting to male Lucar/spade terminals
H4 P43T headlamp socket ceramic connector. 21mm high, 27mm wide and 24mm long. High performance connector with 10cm long blue white and black cable tails.
Fitted to the head lamp units we assemble, BS specified wiring and wire colours. Approximate length 45cm. Single H4 lamp connector block with wired brass flag terminals, wires encased in sleeve...
Wiring harness for H4 headlamps fitted with push fit WEDGE T10 side light bulb holder that accepts capless T10 base bulbs (e.g. B501). Supplied with plastic sheathing and rubber grommet for feed...
Wiring harness for H4 headlight fitted with WEDGE T10 tube type side light bulb holder that accepts capless bulbs (B501) with extra earth wire/terminal for Caterham cars, supplied with plastic...
Wiring harness for H4 headlight fitted with side light connections with female Lucar (6.3mm spade) terminals fitted. Supplied with plastic sheathing and rubber grommet for feed through. BS...
H1 headlamp socket ceramic connector. 11mm high, 15.1mm wide and 25mm long. With 10cm long single cable tail.
H7 headlamp socket ceramic connector. 14.5mm high, 20.5mm wide and 23.5mm long. With two 10cm long single cable tails.
This BA15S male socket connector, fitted with two 10cm wire tails, allows you to create a DIY wiring connection between your conventional bulb holder socket and LED clusters.
This BAY15D male socket connector, fitted with three 10cm wire tails, allows you to create a DIY wiring connection between your conventional bulb holder socket and LED clusters.
This is a conversion kit for traditional Spot, Fog or Driving lights that use the British Pre Focus type bulbs (BPF SC P36S) - enabling use of modern H1 P14.5S base (commonly 55w) bulbs to provide...